- Offizieller Beitrag
Unsinn mit ausbauen, bis dahin bist Du längst fertig mit der Wartung!
Unsinn mit ausbauen, bis dahin bist Du längst fertig mit der Wartung!
das wird eng, wir ziehen auch gerade, ich weiß, geiles timing meinerseits
Vielen Dank für den Tipp mit Brodit. War heute beim Auto und dann war mir klar, dass nur das in Frage kommt.
Das Ding ist super und hält bombenfest.
Allerdings ist die Klammer wirklich sehr massiv.
An die Drucker Gurus, kann man da was machen? Das gegenläufige Gewinde der Klammer würde ich als problematisch einstufen, oder?
Gruß,
Mattes
Ich glaube mal, das für die paar Euros es sich nicht lohnt, eine Vorlage zu basteln und das dann zu drucken. Und dann haste keine vernünftige Klammer zum arretieren.
... nicht wegen den Euros.
Das Ding ist echt gut, aber klobig und extrem schwer.
Wenn man da was schlankes drucken könnte, halbe Breite, super!
Kleine Frage in die Runde:
Ist der folgende Halter „Leather“:
https://www.shapeways.com/product/QZ3SHF…&li=marketplace
auch die richtige Option im Fall von Alcantara?
Herzlichen Dank vorab!
Lars
Alles anzeigenKleine Frage in die Runde:
Ist der folgende Halter „Leather“:https://www.shapeways.com/product/QZ3SHF…&li=marketplace
auch die richtige Option im Fall von Alcantara?
Herzlichen Dank vorab!
Lars
Ich hab ne 2005er Elise, da passt das Teil definitiv nicht (Alcantara). So ein Teil habe ich noch aus dem 3D-Drucker bei mir rumliegen.
Er fährt eine V6. Da meint Alcantara etwas völlig anderes. Ich schätze, das passt.
Alles anzeigenKleine Frage in die Runde:
Ist der folgende Halter „Leather“:https://www.shapeways.com/product/QZ3SHF…&li=marketplace
auch die richtige Option im Fall von Alcantara?
Herzlichen Dank vorab!
Lars
Hi Lars, hatte das gleiche Problem in einem identischen Auto und habe folgendes gemacht:
Den bewährten Brodit ProClip gekauft und dazu noch diese Universal-Handyhalterung.
In den Brodit Clip dann möglichst weit oben (und mittig) ein Loch mit 25mm Durchmesser bohren.
Die Universal-Halterung lässt sich rückseitig zerlegen und dann schön flach auf den Clip montieren. Die Konstruktion hält super (auch bei flotten Kurven) und passt bei mir farblich perfekt zum Cockpit.
Auf dem Alcantara gibt es nur einen minimalen Abdruck. Der regeneriert sich aber sofort nach dem Abnehmen und über Winter lasse ich es ab.
Das Handy blockiert weder die Luftauslässe, noch den DIN-Schacht - sofern das Bohrloch möglichst hoch gesetzt wurde.
Wenn ein Radio vorhanden ist und es über einen USB-Port verfügt, besorgt man sich noch eines dieser kurzen 20cm Kabel und kann aufladen. Ideal.
Ist der folgende Halter „Leather“:
https://www.shapeways.com/product/QZ3SHF…&li=marketplace
auch die richtige Option im Fall von Alcantara?
habe genau das Teil in der Exige V6 - mit Leder - passt perfekt. Ich denke, Alcantara macht da keinen Unterschied - wenn, dann ist Alvantary etwas dünner, in dem Fall kannst Du ja auf der Halter-Unterseite etwas aufkleben (z.B. selbstklebende Samtfolie), damit er stramm genug sitzt...
besser zu lang als zu kurz
Herzlichen Dank für die schnelle Unterstützung!
Beste Grüße aus Maintal, Lars
... Nur noch mal zur Bestätigung: In der Beschreibung des anderen Halter-Designs (mit der etwas tiefer sitzenden Magnethalterung) steht, das er für Leder ODER Alcantara bezogenes dash geeignet ist. Der Längenunterschied beim Bogen ist gerade mal 2mm zum Halter für das unbezogene dash.
Danke nochmal an UBoot fürs design!
... Nur noch mal zur Bestätigung: In der Beschreibung des anderen Halter-Designs (mit der etwas tiefer sitzenden Magnethalterung) steht, das er für Leder ODER Alcantara bezogenes dash geeignet ist. Der Längenunterschied beim Bogen ist gerade mal 2mm zum Halter für das unbezogene dash.
Danke nochmal an UBoot fürs design!
Uboot ist der Beste. Daumen hoch doppelt.gif
Die leichte Halterung mit den Löchern sitzt bei mir perfekt, unauffällig und hält entweder ein Samsung S7, ein Appleschrott 10xs oder ein Samsung PAD.
Alles hält mit dem Magnet an der Halterung.
Wenn ein Handy dran hängt, sind die Düsen frei.
Z.B das Samsung Pad hing locker als Navi und Radionavigation schon mehr als 30K Km ohne runter zu fallen dran. car_062.gif
Wechsel diese Saison auf ein Ipad, welches dann an dem Magneten hängt. crazy_pilot.gif
Ist zwar ein bisschen schwerer als das Samsung Pad... aber ich teste demnächst mal, ob es hält... brutale-224.gif
Ist zwar ein bisschen schwerer als das Samsung Pad... aber ich teste demnächst mal, ob es hält...
und wenn es nicht hält, liegt es ja am yosh Magneten und nicht an der Halterkonstruktion - dann kannst Du den yosh Magneten immer noch gegen einen von diesen mechanischen Motorrad-Handy-Haltern austauschen..
.... Klasse, habe ich genauso bestellt und kann es kaum erwarten..... rechtzeitig zum Saisonstart sollte das Set da sein.... in ein paar Wochen 😉
Ich würde gerne das Design des 3D-Druck Halters etwas anpassen, dass der YOSH Magsafe Qi-Lader mit minmalem Bauraum direkt darauf passt und ggf. einen kleinen Clip als Kabelhalterung integrieren - mal sehen. Dazu bräucht ich aber das editierbare CAD File...
Die Nachrichten-Funktion hier im Forum hat ja oft den Nachteil, dass die keiner liest Hat jemand zufällig die Kontaktdaten von Klaus/Uboot?
vielleicht hat et ja Urlaub. Lesen tut er hier ganz sicher.
sanchezz Hätte Interesse an einem solchen Halter. Yosh MagSafe Lader liegt schon daheim. Gruß Andre
Klaus hat sich gemeldet, ich spiele mal rum. Da Klaus aber die ganze Arbeit hatte, wird wenn dann aber alles über ihn laufen... Wenn da überhaupt was sinnvolles rauskommt
Alles endlich gut geklappt - Halterung sieht gut aus, minimaler Bauraum, Yosh Magnethalterung inkl. induktivem Laden integriert möglichst weit unten.
Leider habe ich aber das Problem, dass sich der Haken oben nach etwas Gerüttel vom Alcantara nach oben arbeitet, dann löst und die ganze Halterung runterpurzelt - obwohl ich den identischen Bügel wie Klaus‘ Alcantara-Halterung verwende.
Eigentlich passt der Bügel perfekt, d.h. kürzer machen oder so würde ich denke ich nichts bringen…
Die Bilder sind bewusst hässliche Blitzbilder für beste Sichtbarkeit; der Haken abgebildet nachdem er sich freigerüttelt hat.
Ideen?
Irgendwelche Ideen? Sonst nehme ich doch die etwas teure und im Vergleich sehr voluminöse Brodit und schraube da die Yosh dran… Wäre aber irgendwie schade; 3D Druck wäre irgendwie cooler 😎
also bei mir hat das Teil immer bombenfest gehalten (den Halter von Klaus über shapeways), hatte allerdings Leder statt Alcantara. Ich vermute, es ist nicht genug Spannung auf dem Halter, Du könntest den Halter mit etwas Samtfolie unterfüttern, nur so viel, daß er richtig auf Spannung ist und das untere ende richtig einrastet.
Ich hatte auch einen Magsafe halter montiert, passt auch an den Standardhalter, musste glaube ich nur die Bohrung für die Schraube auf 2,5 oder 3mm aufbohren...
Mach den Haken oben breiter, also von der Mitte zu beiden Seiten damit mehr halt reinkommt. Evt auch ein bisschen tiefer damit er mehr hintergreift..
Das Problem kenne ich. Die Nase oben ist zu dick und kommt nicht in die Fuge rein. Wie oben beschrieben mit etwas unterfüttern damit mehr Zug drauf kommt, evtl das Alcantara etwas erwärmen um es etwas besser verdrängen können. Kannst auch an der Rückseite der Nase etwas abfeilen.
bevor Du am ende die hässliche Brodit-Halterung nimmst, kannst Du dir auch selbst aus einem Alu-Streifen eine Halterung biegen und da den magsafe dran schrauben - habe ich irgendwann in 2016 mal gemacht und hielt viele Jahre bombenfest, bis ich sie durch den Halter von Klaus ersetzt habe. (die Anleitung ist auch hier irgendwo im thread, finde ich aber gerade nicht wieder....)
schöne Lenkradnabe